6.8mm Remington SPC
The 6.8mm Remington Special Purpose Cartridge (6.8 SPC, 6.8 SPC II or 6.8×43mm) is a rimless bottlenecked intermediate rifle cartridge that was developed by Remington Arms in collaboration with members of the U.S. Army Marksmanship Unit, United States Special Operations Command to possibly replace the 5.56 NATO cartridge in a Short Barreled Rifle(SBR)/Carbine.
Based upon the .30 Remington cartridge, it is midway between the 5.56×45mm NATO and 7.62×51mm NATO in bore diameter. It uses the same diameter bullet (usually not the same weight) as the .270 Winchester hunting cartridge.
Development[edit source | edit]
The 6.8mm SPC cartridge was designed to address the deficiencies of the terminal ballistics of the 5.56×45mm NATO cartridge currently in service with the Armed Forces of all NATO aligned countries. The cartridge was the result of the Enhanced Rifle Cartridge program. The 6.8 SPC (6.8×43mm) was initially developed by MSG Steve Holland and Chris Murray, a United States Army Marksmanship Unit gunsmith, to offer superior downrange lethality over the 5.56 NATO/.223 Remington in an M16 pattern service rifle with minimal loss of magazine capacity and a negligible increase in recoil. The goal was to create a cartridge that would bridge the gap between 5.56 mm and 7.62 mm.
The program started the design by using a .30 Remington case, which was modified in length to fit into magazines that would be accommodated by the magazine wells of the M16 family of rifles and carbines that are currently in service with the U.S. Armed Forces.
In tests comparing various caliber bullets, Holland and Murray determined that a 6.5 mm caliber projectile had the best accuracy and penetration,[clarification needed] with historical data going back for decades of US Army exterior and terminal ballistic testing, but a 7 mm projectile had the best terminal performance.[clarification needed] The combination of the cartridge case, powder load, and projectile easily outperformed the 7.62×39mm and 5.45×39mm Soviet cartridge, with the new cartridge proving to be about 61 m/s (200 ft/s) faster than the 7.62 NATO.[clarification needed] The resulting cartridge was named the 6.8 Remington Special Purpose Cartridge due to the .270" (6.8 mm) diameter projectile and the fact that it was based on the .30 Remington case.
In general, adapting an AR-style rifle to the new cartridge only requires the replacement of the barrel, bolt, magazine & muzzle device (if applicable) of the 5.56 mm-chambered rifle; but to further streamline and simplify the conversion process many parts manufacturers sell complete upper receiver assemblies chambered for 6.8 SPC. While a complete 6.8 SPC assembly is a somewhat more expensive route, the conversion of an existing 5.56 mm/.223 rifle to 6.8 SPC using a complete upper assembly takes less than a minute on an AR-style rifle without the need for specialized tools or skills.
The 6.8mm Remington SPC was designed to perform better in short barreled CQB rifles after diminished performance from the 5.56 NATO when the M16A2 was changed from the rifle configuration to the current M4 carbine. The 6.8 SPC delivers 44% more energy than the 5.56mm NATO (M4 configuration) at 100–300 metres (330–980 ft). The 6.8 mm SPC is not the ballistic equal of the 7.62×51mm NATO cartridge, but it has less recoil, has been said to be more controllable in rapid fire, and is lighter, allowing operators to carry more ammunition than would otherwise be possible with the larger caliber round. The 6.8 mm generates around 2,385 J (1,759 ft⋅lbf) of muzzle energy with a 7.5-gram (115 gr) bullet. In comparison, the 5.56×45mm round (which the 6.8 is designed to replace) generates around 1,796 J (1,325 ft⋅lbf) with a 4.0 g (62 gr) bullet, giving the 6.8 mm a terminal ballistic advantage over the 5.56 mm of 588 J (434 ft⋅lbf). One of the enigmatic features of this cartridge is its being designed for a short barrel carbine length rifle than the standard rifle length is (usually 41 cm (16 in)). The round only gains about 7.6–10.7 m/s (25–35 ft/s) for every 25 mm of barrel length past the standard 410-millimetre (16 in) barrel (all else being equal) up to barrel's length around 560–610 mm (22–24 in) with no gain/loss in accuracy. It also does very well in rifles with less than 410 mm (16 in) barrels. In recent developments (the period 2008-2012) the performance of the 6.8 SPC has been increased by approximately 61 to 91 m/s (200 to 300 ft/s) by the work of one ammunition manufacturer Silver State Armory LLC (SSA) and a few custom rifle builders using/designing the correct chamber and barrel specifications. The 6.8mm Remington SPC cartridge weighs depending on the manufacturer and load between 16.8 and 17.6 grams (259 and 272 gr). Also, more recently, LWRC, Magpul and Alliant Techsystems (ATK) are currently introducing a new AR-15 designed for the 6.8 SPC which allows for a proprietary 6.8 Magpul P-Mags and an overall cartridge length of 5.9 centimetres (2.32 in). The Personal Defense Weapon (PDW) known as the Six8 is SPC II w 1:250 millimetres (10 in) twist and is able to use all current 6.8 SPC factory ammunition. See Gold Dot below for ATK's part.
Muzzle velocity from a 610-millimetre (24 in) barrel[edit source | edit]
|* 7.1-gram (110 gr) Nosler Accubond||870 m/s (2,840 ft/s)- Silver State Armory (SSA)|
|* 7.5-gram (115 gr) OTM||850 m/s (2,800 ft/s)- Remington Premier Match|
|* 5.5-gram (85 gr) Nosler E-Tip||940 m/s (3,100 ft/s) - Silver State Armory (SSA)|
|* 5.8-gram (90 gr) Nosler BSB||910 m/s (2,980 ft/s) - Silver State Armory (SSA)|
|* 7.1-gram (110 gr) Hornady BTHP TAP||820 m/s (2,700 ft/s) - Hornady Law Enforcement "tactical" factory load|
|* 7.5-gram (115 gr) OTM (FMJ)||831 m/s (2,725 ft/s)} - Silver State Armory (SSA)|
|* 7.5-gram (115 gr) Boat Tail Hollow Point (BTHP)||850 m/s (2,800 ft/s)|
|* 7.5-gram (115 gr) Sierra Match King (SMK)||850 m/s (2,800 ft/s)|
|* 7.1-gram (110 gr) Hornady V-MAX||850 m/s (2,800 ft/s)|
|* 7.1-gram (110 gr) SCHP||850 m/s (2,800 ft/s) - Silver State Armory (SSA) "combat" factory load|
|* 7.1-gram (110 gr) BTHP OTM & Barnes TSX||840 m/s (2,750 ft/s) - Wilson Combat factory load|
|* 5.5-gram (85 gr) Barnes TSX||970 m/s (3,180 ft/s) - Silver State Armory (SSA) "tactical" factory load|
|* 5.8-gram (90 gr) Speer Gold Dot||930 m/s (3,050 ft/s)- Federal(ATK) "tac/mil" load.|
Muzzle velocity from a 510-millimetre (20 in) barrel[edit source | edit]
- 7.1-gram (110 gr) Nosler Accubond ; 850 m/s (2,800 ft/s)- Silver State Armory (SSA)
- 7.5-gram (115 gr) OTM ; 820 m/s (2,700 ft/s)- Remington Premier Match
- 6.2-gram (95 gr) Barnes TTSX ; 880 m/s (2,880 ft/s) - Doubletap
- 5.8-gram (90 gr) Bonded Defense JSP ; 910 m/s (2,980 ft/s) - Doubletap
- 6.5-gram (100 gr) Nosler Accubond ; 855 m/s (2,805 ft/s) - Doubletap
- 7.1-gram (110 gr) Nosler Accubond ; 830 m/s (2,710 ft/s) - Doubletap
- 7.5-gram (115 gr) Full Metal Jacket Boat Tail ; 806 m/s (2,645 ft/s) - Doubletap
- 5.8-gram (90 gr) Speer® TNT ; 910 m/s (2,980 ft/s)- Silver State Armory (SSA)
Muzzle velocity from a 410-millimetre (16 in) barrel[edit source | edit]
- 7.1-gram (110 gr) Nosler Accubond ; 820 m/s (2,700 ft/s)- Silver State Armory (SSA)
- 7.5-gram (115 gr) OTM ; 800 m/s (2,625 ft/s)- Remington Premier Match
- 5.5-gram (85 gr) Barnes TSX ; 920 m/s (3,030 ft/s) - Silver State Armory (SSA)
- 5.5-gram (85 gr) Nosler E-Tip ; 900 m/s (2,950 ft/s) - Silver State Armory (SSA)
- 5.8-gram (90 gr) Nosler BSB ; 870 m/s (2,840 ft/s) - Silver State Armory (SSA)
- 7.1-gram (110 gr) Hornady V-MAX : 810 m/s (2,650 ft/s)
- 7.5-gram (115 gr) Sierra Match King (SMK): 810 m/s (2,650 ft/s)
- 7.5-gram (115 gr) OTM (FMJ): 785 m/s (2,575 ft/s)} - Silver State Armory (SSA)
- 5.5-gram (85 gr) Barnes TSX ; 940 m/s (3,070 ft/s) - Silver State Armory (SSA) "tactical" factory load
- 5.8-gram (90 gr) Speer Gold Dot 880 m/s (2,900 ft/s)- Federal(ATK) "tac/mil" load.
- 6.2-gram (95 gr) Barnes TTSX: 790 m/s (2,600 ft/s) - Wilson Combat factory load
- 7.1-gram (110 gr) SCHP; 810 m/s (2,650 ft/s) - Silver State Armory (SSA) "combat" factory load
- 7.1-gram (110 gr) Hornady BTHP TAP; 780 m/s (2,550 ft/s) - Hornady Law Enforcement "tactical" factory load
- 7.1-gram (110 gr) BTHP OTM & Barnes TSX; 790 m/s (2,600 ft/s) - Wilson Combat factory load
- 9.1-gram (140 gr) Berger VLD; 732 m/s (2,401 ft/s) - Silver State Armory (SSA) factory load. (Discontinued)
Comparison to other military calibers[edit source | edit]
|Cartridge||Muzzle velocity||180 metres (200 yd) drop||180 metres (200 yd) velocity||370 metres (400 yd) drop||370 metres (400 yd) velocity|
|5.56×45mm 3.6 g (55 gr) M193||937 m/s (3,073 ft/s)||56 mm (2.2 in)||717 m/s (2,353 ft/s)||710 mm (27.8 in)||531 m/s (1,743 ft/s)|
|5.56×45mm 5.0 g (77 gr) OTM||817 m/s (2,679 ft/s)||84 mm (3.3 in)||675 m/s (2,216 ft/s)||830 mm (32.7 in)||550 m/s (1,810 ft/s)|
|6.8×43mm SPC 7.5 g (115 gr) SMK||810 m/s (2,650 ft/s)||89 mm (3.5 in)||653 m/s (2,143 ft/s)||900 mm (35.4 in)||511 m/s (1,677 ft/s)|
|6.8×43mm SPC 7.1 g (110 gr) V-MAX||810 m/s (2,650 ft/s)||84 mm (3.3 in)||673 m/s (2,208 ft/s)||790 mm (31.1 in)||552 m/s (1,811 ft/s)|
|7.62×39mm||700 m/s (2,300 ft/s)||84 mm (3.3 in)||545 m/s (1,787 ft/s)||1,370 mm (53.8 in)||404 m/s (1,324 ft/s)|
|7.62×51mm 10.9 g (168 gr) SMK||790 m/s (2,600 ft/s)||86 mm (3.4 in)||681 m/s (2,235 ft/s)||820 mm (32.3 in)||576 m/s (1,891 ft/s)|
Typical trajectory information from carbines with drop and velocity calculated at sea level with a 91 metres (100 yd) zero.
ATK Gold Dot[edit source | edit]
When the LWRC Six8 was being developed, Alliant Techsystems was contracted to develop a new 6.8×43mm round for the weapon. Unlike smaller commercial firms, ATK is a large ammunition supplier that delivers products for the U.S. Army, so it had large resources and manufacturing capabilities at its disposal. Commercial cartridges varied in case capacity and thickness, but LWRC wanted a thick and durable case for military uses. A 90 gr (5.8 g) load was developed specifically for a high muzzle velocity and low felt recoil from the Six8's 8.5 in (220 mm) barrel. Effective range would be over 300 yd (274 m) and the bullet would still have enough energy to penetrate intermediate barriers. Three 90 gr loads were constructed for testing that included Gold Dot, Monolithic Hollow Point, and FMJ. The Gold Dot bullet was selected with a .035 in (0.89 mm) jacket and a bonded core. The propellant was designed for reduced muzzle flash stable performance at temperatures between -29.2 to 125.6 degrees F. Muzzle velocity averaged at a 200 ft/s (61 m/s) difference at the required temperature extremes from the 8.5 in barrel. From a 24 in (610 mm) barrel, the round produced a group of 1.56 in (40 mm) at 200 yd (183 m).
|Barrel length||Muzzle velocity||Muzzle energy|
|220 mm (8.5 in)||750 m/s (2,450 ft/s)||1,626 J (1,199 ft⋅lb)|
|410 mm (16 in)||880 m/s (2,900 ft/s)||2,280 J (1,680 ft⋅lb)|
|610 mm (24 in)||930 m/s (3,050 ft/s)||2,519 J (1,858 ft⋅lb)|
Applications[edit source | edit]
Military/law enforcement adoption[edit source | edit]
By late 2004 the 6.8×43mm SPC was said to be performing well in the field against enemy combatants in Special Operations. However the cartridge was not used by conventional US military personnel. It was not adopted for widespread use due to resistance from officials. The 6.8 SPC was designed for better terminal effectiveness at the shorter ranges of urban combat experienced in Iraq. When fighting in Afghanistan began to intensify, engagements began taking place at greater distances, where 6.8 SPC begins to falter. Experiments suggested that the comparatively short 6.8 mm bullets became ineffective at longer ranges. In 2007, both the U.S. SOCOM and the U.S. Marine Corps decided not to field weapons chambered in 6.8 mm due to logistical and cost issues. An unnamed LWRC representative said in January 2014 that the US military is once again taking a look at the 6.8 SPCII after all the commercial development in the last 10 years.
While there are many rumors of evaluations of the cartridge by several major Federal and local law enforcement agencies, the US Drug Enforcement Administration has allowed individual agents to purchase the M6A2 D-DEA - which uses the 6.8mm Remington SPC - as an authorized alternative to their duty weapon. In 2010 the Jordanian state-owned arms manufacturer KADDB announced that they would be producing 6.8 mm rifles and carbines for the Jordanian Army. There is also a contract between LWRC, Magpul, Alliant Techsystems and The Saudi Royal guard for around 36,000 Six8 PDWs & undisclosed amount of ATK/Federal XD68GD (90gr Gold Dot 'training' ammo) and proprietary Magpul 6.8 Pmags specifically for the LWRC Six8. See above under the subsection 'Development' Section. The 6.8 is also being produced in a Squad Automatic Weapon or SAW by U.S. Machine Gun Armory. The MGA SAW™ is fully compatible with the United States Department of Defense model designations: M249 and MK46. It is currently being shipped to US allies and is under testing with the US military.
Current chamberings[edit source | edit]
There are several different chambers for the 6.8 SPC which yield different results. They are:
- Original Murray 6.8×43 ERC developed in 2002.
- The Remington SAAMI submitted specifications. It was supposed to have a 1.3 mm (0.050 in) freebore, 45° cone angle, 7.1 mm (0.278 in) ⌀ freebore. The reamers and PTG prints had an 80° neck to freebore cone angle, which was a result of a mistake in the reamer drawing submitted, and was never corrected by the reamer maker or Remington during the process of tooling up for the testing protocols that eventually drove the SAAMI submission.
- SPC II is current standard chamber used by most barrel manufactures. It has been said to be very close to the original Enhanced Rifle Cartridge Program chamber. It has a 2.5 mm (0.100 in) freebore, 45° cone angle, 7.1 mm (0.278 in) ⌀ freebore, and 7.84 mm (0.3085 in) neck.Template:Updateinline
- Murray DMR chamber, which was meant to address improved accuracy expectations for the ERC Special Purpose Rifle program in SOCOM.
- 6.8 ARP created by AR Performance. It has a 2.4 mm (0.095 in) freebore, 45° cone angle, and a 7.05 mm (0.2775 in) ⌀ freebore, and 7.84 to 7.85 mm (0.3085 to 0.309 in) neck.
- Noveske Mod 1 designed by Noveske Rifleworks LLC. It has been said to have a 2.5 mm (0.100 in) freebore.
- Bison Armory 6.8 Bison, introduced December 2017, which decreases the freebore of the 6.8 SPC II chamber to1.8 mm (0.072 in).
Only the rifles chambered with the newer specified chamber (6.8mm Spec II, Noveske Mod 1, 6.8 ARP, and 6.8 Bison chambers) can safely use the higher pressure military/tactical and near max-maximum handloaded ammunition. Those rifles using the Original SAAMI specs should only be used with the standard commercial cartridge pressure (Specified by SAAMI).
Twist Rate[edit source | edit]
Several twist rates are available for 6.8 SPC barrels. The slowest twist rates are approximately 1:12", while twist rates between 1:9.5" and 1:11" are common. The de facto standard twist rate for 6.8 SPC is currently 1:11". Bison Armory employs a twist rate of 1:7" in some of their 16" and shorter barrels in order to stabilize 180 to 200 grain bullets for subsonic performance similar to the 300 AAC Blackout.
Semiautomatic action[edit source | edit]
The first major manufacturer to offer a 6.8mm Remington SPC chambered version of the AR-15 was Barrett Firearms Company, offering the Barrett M468 and later the REC7. By 2007, most major manufacturers of AR-15 type rifles for the civilian gun market were offering rifles in this caliber. Dedicated AR upper receiver assemblies chambered for the round are produced by a number of smaller firms, including Daniel Defense. Ruger Firearms no longer produces a 6.8 mm for their Ruger SR-556 piston-driven AR-15 variant. The Stag Arms Hunter and Tactical models utilize the newer chamber(SPC II) and specified twist rates to accommodate higher pressure loadings, as well as upper receivers in Left-Handed configurations. Rock River Arms has a LAR-6.8 X Series rifle and uppers. Microtech Small Arms Research offers their version of the Steyr AUG in 6.8. Robinson Armament Co. offers the XCR-L in 6.8, which can be easily converted between 6.8, 5.56, and 7.62×39. Bushmaster has delivered a 6.8 SPC II conversion kit to the market as of October 2018. Ruger Firearms chambered their Mini-14 Ranch Rifle in this round for several years; however, it has been discontinued.
Manual action[edit source | edit]
As of 2019, no significant firearms companies are producing a manual action firearm in 6.8 SPC. Remington used to make a bolt-action rifle chambered for 6.8 SPC, a 610-millimetre (24 in) barrel Model 700 but this item is not currently available from Remington. Ruger no longer produces their M77 Hawkeye Compact rifle with a 420-millimetre (16.5 in) barrel weighing in at 2.7 kilograms (6.0 lb). Browning has discontinued their A-Bolt rifles in all calibers including the formerly available 6.8 SPC. Thompson/Center has offered barrels chambered for 6.8 SPC for the Encore and Contender G2.
See also[edit source | edit]
- .224 Valkyrie - 6.8 SPC derivative cartridge
- 6 mm caliber and 7 mm caliber — other cartridges of similar size
- 6mm SAW — similar cartridge developed to approximate both 7.62×51mm and 5.56×45mm cartridges.
- .280 British — similar cartridge developed during the 1940s in the UK
- .276 Pedersen — similar cartridge developed in 1923 in the US.
- .277 Wolverine — 6.8mm AR-15 wildcat based on 5.56×45mm case
- List of AR platform calibers
- List of individual weapons of the U.S. Armed Forces
- 6.5×42mm, also known as 6.5 MPC (Multi Purpose Cartridge), based on a necked down .223 Remington case.
Notes[edit source | edit]
- Not a private endeavor or fully sanctioned government project
- "30 Rem". Chuckhawks.com. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- John Pike. "5.56-mm Cartridges". Globalsecurity.org. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- "Archived copy". Archived from the original on 2015-05-04. Retrieved 2015-03-21.CS1 maint: archived copy as title (link)
- "6.8 mm SPC Cartridge History & Development. Hornady's Ammunition. The Stag Carbine". Demigodllc.com. 2006-07-31. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- Paul, Gary (2011-01-04). "The 6.8mm Remington SPC". Rifleshootermag.com. Archived from the original on 2010-11-24. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- "6.8 mm SPC Cartridge History & Development. Hornady's Ammunition. The Stag Carbine". Demigodllc.com. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- "Archived copy" (PDF). Archived from the original (PDF) on 2014-02-21. Retrieved 2014-02-10.CS1 maint: archived copy as title (link)
- "DTIC.mil". Archived from the original on 2011-06-29. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- "Archived copy". Archived from the original on 2012-04-23. Retrieved 2012-05-18.CS1 maint: archived copy as title (link)
- "110 gr. Hornady BTHP, 2600 FPS - 16" Barrel-Wilson Combat". Shopwilsoncombat.com. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- "6.8mm SPC article". Demigodllc.com. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- LWRCI UCIW SIX8 Review - Shotgunnews.com, 9 November 2012
- Another 7.62mm Bullet For M-16s - Strategypage.com, 8 January 2012
- The 6.5×40 Cartridge: Longer Reach for the M4 & M16 - SAdefensejournal.com, 26 March 2014
- Dan Lamothe. "Corps to pass on Army upgrades to M4". Army Times Publishing Company. Archived from the original on 2010-09-25. Retrieved 11 September 2010. CS1 maint: discouraged parameter (link)
- "LWRC: 6.8 SPC is the New 300 Blackout". Archived from the original on 2014-11-10. Retrieved 2014-11-10.
- "LWRC rifles to be license-produced in Jordan". Thefirearmblog.com. 2010-05-13. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- "Information on the 6.8 SPC Mini". Ruger-firearms.com. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- "Information on the 6.8 Ruger Hawkeye Compact". Ruger.com. Archived from the original on 2010-01-13. Retrieved 2011-09-15. CS1 maint: discouraged parameter (link)
- The 6.5 MPC cartridge by SSK developed by J.D. Jones at SSK Industries | Article on DefenseReview.com
[edit source | edit]
- Definitive history of 6.8 SPC- The 6.8 SPC, Is it all that?
- 6.8 SPC FAQ
- Remington Ammunition Information
- M468 Rifle
- Defense Review
- Gunblast.com article
- Sharper Shooting: Upgrading Ammunition Lethality
- First Look: The 6.8mm Remington SPC
- 6,8 SPC
- 6.8mm SPC Cartridges Available, Silver State Armory Ammunition Manufacturer
Visibility[edit source | edit]
This page has been added to search engine indexes. learn more